Gun enthusiasts want the best when it comes to protecting their firearms and customized finishes. Especially when those finishes include ferrous metals, wood, stainless steel, synthetics, and alloys. There is no heating or baking required. Here are a few tips on using DuraCoat Aerosol, and be sure to ask your Lawrence, KS supplier about Peel 'N Spray templates.
For people who prefer a difference in the appearance of their guns, DuraCoat offers different textures to please most gun owners including varieties of camo and pearl. Some people create layers of textures and mix and blend colors to help identify their firearm from that of anyone else.
One of the nice things about this product is the hardener that comes with it. The aerosol can is a can within a can and allows putting the hardener in without making a huge mess. The usual ratio of 12 parts DuraCoat to 1 part hardener, and greatly speeds up the drying process. Change the ratio to 10:1 for a higher glossy finish that shines like brand new.
When using stick on templates, use mineral spirits and a clean rag. The mineral spirits will not affect the finish of your project but will remove only the residual stickiness from the adhesive compound. When completed the surface is free of any sticky feeling and the degree of intended gloss is not adversely affected. Please remember to clean thoroughly the weapon before applying any clear coat product.
For the fastest drying time, many gun owners use a heat setting of 110 degrees F for about 1 hour to speed up the process and reassemble their weapons. Once the surface is completely dry most cleaners, abrasive solvents and lubricants will not harm the new finish. For best results allow three to six weeks for full drying and curing.
Keep in mind that DuraCoat is available in over 200 colors, including Clear and those 200 colors when mixed will match any color in the spectrum. The Aerosol Kit contains a spray can that easily allows mixing the dryer with the color mixture for perfect results and easy to access and clean up afterward.
Before getting started be sure to use a good cleaner to remove all the dirt and debris that accumulates, even if the firearms stored in a closet or gun bag. DuraCoat Cleaner dries immediately and leaves no residue or film thereby ensuring a smooth and attractive finish.
Always dismantle a gun for safety reasons before attempting to clean it, repair it, or refinish it. Make sure all compartments have no ammunitions in them. Check the cylinder, the bullet clip and chamber to make sure the gun is unloaded. Then dismantle it and mask off any areas not intended for DuraCoat before spraying the product on the pieces.
Even the smallest speck of dust can render a firearm useless if lodged in an area of tight tolerances and precision accuracy. It is important to keep all firearms properly cleaned and maintained for maximum safety. Ask your local gun store owner about the benefits of protective coatings that help ensure enjoyable gun ownership.
For people who prefer a difference in the appearance of their guns, DuraCoat offers different textures to please most gun owners including varieties of camo and pearl. Some people create layers of textures and mix and blend colors to help identify their firearm from that of anyone else.
One of the nice things about this product is the hardener that comes with it. The aerosol can is a can within a can and allows putting the hardener in without making a huge mess. The usual ratio of 12 parts DuraCoat to 1 part hardener, and greatly speeds up the drying process. Change the ratio to 10:1 for a higher glossy finish that shines like brand new.
When using stick on templates, use mineral spirits and a clean rag. The mineral spirits will not affect the finish of your project but will remove only the residual stickiness from the adhesive compound. When completed the surface is free of any sticky feeling and the degree of intended gloss is not adversely affected. Please remember to clean thoroughly the weapon before applying any clear coat product.
For the fastest drying time, many gun owners use a heat setting of 110 degrees F for about 1 hour to speed up the process and reassemble their weapons. Once the surface is completely dry most cleaners, abrasive solvents and lubricants will not harm the new finish. For best results allow three to six weeks for full drying and curing.
Keep in mind that DuraCoat is available in over 200 colors, including Clear and those 200 colors when mixed will match any color in the spectrum. The Aerosol Kit contains a spray can that easily allows mixing the dryer with the color mixture for perfect results and easy to access and clean up afterward.
Before getting started be sure to use a good cleaner to remove all the dirt and debris that accumulates, even if the firearms stored in a closet or gun bag. DuraCoat Cleaner dries immediately and leaves no residue or film thereby ensuring a smooth and attractive finish.
Always dismantle a gun for safety reasons before attempting to clean it, repair it, or refinish it. Make sure all compartments have no ammunitions in them. Check the cylinder, the bullet clip and chamber to make sure the gun is unloaded. Then dismantle it and mask off any areas not intended for DuraCoat before spraying the product on the pieces.
Even the smallest speck of dust can render a firearm useless if lodged in an area of tight tolerances and precision accuracy. It is important to keep all firearms properly cleaned and maintained for maximum safety. Ask your local gun store owner about the benefits of protective coatings that help ensure enjoyable gun ownership.
No comments:
Post a Comment